Get complete plans to build your own HHO generator
based on the research of Stanley Meyer. This is not electrolysis!
This breakthrough technology does not use an
electrolyte, just distilled water. It runs cool and will not use more
than a few amps (unlike electrolysis designs using plates). Just
$47 + ($3.95 S&H) for the CD plus instant download!
Call Toll Free to Order by Phone:
Dry Cell 4x4" 11 plate $229
1.5 - 3 Liters Per Minute - Includes Installation Kit
All new S-Cell series
Model:12V 1-3 LPM 12V injection molded HHO system.
This is a very compact unit,
4"X4"X3" so it is ideal for vehicles with limited room.
System is engineered to outlast
and outperform any other cell on the market!
System includes our single "S" series cells, water reservoir, hose and
Uses our high grade super alloy electrodes! Our electrodes rock! Electrodes are
18 gauge 316L stainless steel for great durability.
Engineered to use a relatively low concentration of electrolyte. Potassium or
Sodium Hydroxide. No major foaming or overheating issues , has excellent
through design. As the electrolyte circulates through the unit it cools
permitting higher amperage for higher output.
Each electrode is framed in its
own insulating pocket.~ Zero current leakage! All electrode connections are
framed and insulated in a separate injection molded compartment within the cell.
The electrode connection areas remain dry and are not exposed to electrolysis or
HHO gas.. this makes the unit one of the safest designs on the market.
Please Note: This is not a
Stanley Meyer type design though it does have some similarities. It uses a weak
solution of Potassium Hydroxide and distilled water and draws under 19 amps. It
will probably draw even fewer amps when connected via our new PWM!
Price with fittings: $229.00.
Shipping and handling is $15 domestic USA or $25 international.
21 Plate Dry Cell HHO Generator: $27900
Complete With Installation Kit
For engines exceeding 7 liters and big marine diesel
engines I recommend hooking up two of these units in series along with
a constant current Dave Lawton design PWM.
Two of these Dry Cell generators will produce large
volumes of HHO gas because unlike our competitors we use high
temperature resistant Lexan™ and we cross sand (etch) the plates for
more surface area. Beware any similar unit that appears smooth, bright
and shiny as it will produce far less HHO.
3 - 7 Liters Per Minute
A must for V-8 and 6+ liter Diesels
All new S-Cell series Model:12V 1-3 LPM 12V
injection molded HHO system. System is engineered to outlast and outperform any other cell on the
~System includes our single "S" series cells, water
reservoir, hose and fittings.
Uses our high grade super alloy electrodes - 18 gauge 316L Laser cut
stainless steel plate that has been cross sanded for maximum surface
The highest quality SS plate means greater
durability and less brown muck you find with lower quality SS.
Engineered to use a relatively low concentration of electrolyte.
Potassium or Sodium Hydroxide work best but this unit will work fine
on Sodium Citrate, a non-toxic electrolyte. No major foaming or overheating issues
because of the excellent flow through design.
Each electrode is framed in its own insulating
pocket.~ Zero current leakage! All electrode connections are framed
and insulated in a separate injection molded compartment within the
cell. The electrode connection areas remain dry and are not exposed to
electrolysis or HHO gas.. this makes the unit one of the safest
designs on the market. Please note that these are hydrogen on
demand generators. They are extremely safe as no HHO gases are stored.
We always use a bubbler in between the intake manifold and the H2O
reservoir to reduce the risk of any kind of backflash reaching the HHO
Please Note: This
is not a Stanley Meyer type design though it does have some
similarities. It uses a weak solution of Potassium Hydroxide and distilled water and draws
under 19 amps. It will probably draw even fewer amps when connected
via our new PWM!
Price with fittings: $279.00.
Shipping and handling is $20 domestic USA or $40 international.
NEW!: Latest Dave Lawton PWM Design
Pulse Width Modulator
allow 14 days before this unit can be shipped due to large demand
for this quality PWM. For more info CLICK
Continuous PWM for Hydrogen
Electronic Fuel Injection
City & Highway Switchable EFIE
The unit is easy to adjust for best fuel economy in
the city using the city dial for below 40 MPH. Adjust the highway dial
for over 40 MPH.
This is a compact unit you can install in, on or below
your dash so you can adjust it while driving. It also has an HHO
"off" toggle so you can return to stock settings.
If you install any HHO generator
on your fuel injected vehicle your car's O2 sensor(s) will cause
your engine to run rich. You may actually get worse gas mileage! For
most vehicles an EFIE unit is the solution. Check with your mechanic
to see if your vehicle has more than one O2 sensor.
If you have more than one wire on your sensor, then
you will have to find out which one is the O2 sensor. Our EFIE WILL
WORK with all Narrow Band O2 sensors. Unit
will work with ONE (1) or TWO (2) O2 Sensors,
Remember, you need an EFIE for
Sensor in your car unless the second O2 sensor is AFTER the
catalytic converter. Disregard all O2 sensors located after the
Complete installation instructions
If you have a WIDE BAND O2
sensor, then this will not work. We are currently developing an EFIE
for WIDE BAND O2 sensors, and if you do need one, please give us a
call at 866-375-6941.
This EFIE is a SINGLE EFIE for a single O2 sensor. This
will only work with one O2 sensor. If you have two O2 sensors,
then we recommend getting 2 of them. We are working on
making a DUAL City/Highway EFIE for vehicles with two O2 sensors.
This EFIE can be mounted under the dash or under
the HOOD. All setup instructions come with the unit. Total of 6
Parts are warranted
to be free from defects when shipped for 30 days from date of
Technologies disclaims any warranties (express or implied),
merchantability, or fitness for any particular purpose.
Experimenting with Hydrogen is extremely hazardous. Customer agrees
by purchasing any products from this site that customer is solely
responsible for his own safety. The company shall in no event be
held liable to any party for any direct, indirect, punitive,
special, incidental or other consequential damages arising directly
or indirectly from any use of components, which are provided “as
is”, and without warranties as to fitness for any purpose.
always, the advice of a competent legal, engineering, accounting or
other professional should be sought. The author and company,
Powergate Technologies, do not warrant the performance, effectiveness
or applicability of any mechanical system built with components sold
on this web site. All links are for information purposes only and
are not warranted for content, accuracy or any other implied or
If you prefer call 866-375-6941 to order with Visa or
MasterCard by phone 7 am - 7pm EST Monday thru Friday. Weekends by
Mail Orders, call for Shipping
and Handling charges then